Chamberlain PD300D Manual do Utilizador

The Chamberlain Group, Inc.845 Larch AvenueElmhurst, Illinois 60126-1196www.chamberlain.comGARAGE DOOR OPENERModel PD300D • 1/2 HPFor Residential Use

10To avoid possible SERIOUS INJURY to fingers frommoving garage door opener:• ALWAYS keep hand clear of sprocket while operatingopener.• Securely atta

11INSTALLATIONASSEMBLY STEP 5Tighten the Chain • Spin the inner nut and lock washer down thetrolley threaded shaft, away from the trolley.• To tighten

12INSTALLATION STEP 1Determine the Header BracketLocationInstallation procedures vary according to garage doortypes. Follow the instructions which app

13Lag Screws5/16"x9x1-5/8"– Finished Ceiling –DoorSpringHeader WallUPCeiling Mounting Holes6" (15 cm) MaximumHeaderBracketVerticalCente

14INSTALLATION STEP 3Attach the Rail to the HeaderBracketNOTE: (Optional) With some existing installations,you may re-use the old header bracket with

15ONE-PIECE DOOR WITHOUT TRACKA 2x4 on its side is convenient for setting an idealdoor-to-rail distance. • Remove foam packaging.• Raise the opener on

16INSTALLATION STEP 5Hang the OpenerThree representative installations are shown. Yoursmay be different. Hanging brackets should be angled(Figure 1) t

17To prevent possible SERIOUS INJURY or DEATH fromelectrocution:• Be sure power is not connected BEFORE installing doorcontrol.• Connect ONLY to 24 VO

18INSTALLATION STEP 7Install the Light• Press the release tabs on both sides of lens.Gently rotate lens back and downward until thelens hinge is in th

19INSTALLATION STEP 9Electrical RequirementsTo avoid installation difficulties, do not run theopener at this time.To reduce the risk of electric shock

2TABLE OF CONTENTSWhen you see these Safety Symbols and SignalWords on the following pages, they will alert you tothe possibility of serious injury or

20Invisible Light BeamProtection AreaSafety Reversing Sensor6" (15 cm) max. above floorSafety Reversing Sensor6" (15 cm) max. above floorFac

21DOOR TRACK MOUNT (RIGHT SIDE)IndicatorLightLensLip SensorBracketDoorTrackFLOOR MOUNT (RIGHT SIDE)WALL MOUNT (RIGHT SIDE)IndicatorLightSensorBracketL

22Carriage Bolt 1/4"-20x1/2"LensWing Nut1/4"-20Figure 5MOUNTING AND WIRING THE SAFETYREVERSING SENSORS• Slide a 1/4"-20x1/2"

23Fiberglass, aluminum or lightweight steel garage doorsWILL REQUIRE reinforcement BEFORE installation ofdoor bracket. Contact your door manufacturer

24Header WallVerticalCenterline ofGarage DoorFinished CeilingOptionalPlacementof DoorBracketHeaderBracketDoorBracket2x4 SupportFor a door with no expo

25INSTALLATION STEP 12Connect Door Arm to TrolleyFollow instructions which apply to your door type asillustrated below and on the following page.SECTI

26ALL ONE-PIECE DOORS1. Assemble the door arm, Figure 4:• Fasten the straight and curved door arm sectionstogether to the longest possible length (wit

27ADJUSTMENT STEP 1Adjust the UP and DOWN TravelLimitsLimit adjustment settings regulate the points at whichthe door will stop when moving up or down.

28ADJUSTMENT STEP 2Adjust the ForceForce adjustment controls are located on the backpanel of the motor unit. Force adjustment settingsregulate the amo

29Without a properly installed safety reversal system,persons (particularly small children) could beSERIOUSLY INJURED or KILLED by a closing garagedoo

3To prevent damage to garage door and opener:• ALWAYS disable locks BEFORE installing and operatingthe opener. • ONLY operate garage door opener at 12

30OPERATION Using Your Garage Door OpenerYour Security✚®opener and hand-held remotecontrol have been factory-set to a matching codewhich changes with

31To Open the Door ManuallyDISCONNECT THE TROLLEY:The door should be fullyclosed if possible. Pull downon the emergency releasehandle (so that the tro

32CARE OF YOUR OPENERLIMIT AND FORCE ADJUSTMENTS:Weather conditions maycause some minor changesin door operation requiringsome re-adjustments,particul

33HAVING A PROBLEM?(TROUBLESHOOTING)1. My door will not close and the light bulbs blinkon my motor unit: The safety reversing sensormust be connected

34Installed Safety Reversing SensorSafety Reversing SensorBell WireDiagnosticsLocated On Motor UnitLED or Diagnostic LED"Learn" Button Your

*3-Button RemotesIf provided with your garage door opener, the largebutton is factory programmed to operate it. Additionalbuttons on anySecurity✚®3-Bu

361. Press and release the “learn”button on motor unit. The learnindicator light will glow steadilyfor 30 seconds.2. Within 30 seconds, enter a fourdi

791011NOTICE56814121332315426Installation Parts37REPAIR PARTSRail Assembly PartsKEY PARTNO. NO. DESCRIPTION1 4A1008 Master link kit2 41C5141-1 Complet

Motor Unit Assembly Parts3821081314151945391612181117167DNUPBrownWire(Down)ContactLIMIT SWITCHASSEMBLYGreyWireYellowWire(Up)ContactCenter LimitContact

39ACCESSORIES LOCKLIGHTCLOSEDOPENLOCKLIGHT3-Button SECURITY✚®RemoteControl:Includes visor clip.SECURITY✚®Keyless Entry:Enables homeowner to operategar

4Safety Reversing SensorHorizontal and vertical reinforcementis needed for lightweight garage doors(fiberglass, steel, aluminum,door with glass panels

© 2007, The Chamberlain Group, Inc.114A3437 All Rights ReservedCHAMBERLAIN SERVICEIS ON CALLOUR LARGE SERVICE ORGANIZATIONSPANS AMERICAINSTALLATION AN

5AccessDoorSafetyReversing SensorSafetyReversingSensorGap between floor and bottom of doormust not exceed 1/4" (6 mm).DoorBracketStraightDoorArmG

62-Conductor Bell WireWhite & White/RedChain and Cable inDispensing CartonCurved DoorArm SectionStraight DoorArm SectionSafety LabelsandLiterature

7Wing Nut 1/4"-20 (2) Handle Nut 5/16"-18 (8) Ring Fastener (3) Spacer (2) Carriage Bolt 1/4"-20x1/2" (2) Insulated Staples (30)

FRONT RAIL(TOP)KEEP LARGERHOLE ON TOP8ASSEMBLY STEP 1Assemble the Rail & Install the TrolleyTo avoid installation difficulties, do not run thegara

9To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top ofthe opener.ASSEMBLY STEP 2Fasten the Rail to the M