Chamberlain WD832KD Manual do Utilizador

The Chamberlain Group, Inc.845 Larch AvenueElmhurst, Illinois 60126-1196www.chamberlain.comGARAGE DOOR OPENERModel WD832KD 1/2 HPFor Residential Use O

TrolleyConnectorIdler PulleyRetainingSlotRoundHoleSpring NutMotor UnitSprocketMountingPlateHex Screws#8x3/8"Belt CapRetainerHex Screw 8x3/8"

11ASSEMBLY STEP 5Set the Tension• Insert a screwdriver tip into one of the nut ring slots and brace it firmly against the trolley.• Place a 7/16&quo

12INSTALLATION STEP 1Determine the Header Bracket LocationInstallation procedures vary according to garage door types. Follow the instructions which a

13Lag Screws5/16"x9x1-5/8"– Finished Ceiling –DoorSpringHeader WallUPCeiling Mounting Holes6" (15 cm) MaximumHeaderBracketVerticalCente

14Opener Carton orTemporarySupportGarageDoorHeader BracketIdler PulleyHeader WallHeaderBracketMounting HoleClevis Pin 5/16"x1-1/2"Ring Faste

15ONE-PIECE DOOR WITHOUT TRACKA 2x4 on its side is convenient for setting an idealdoor-to-rail distance. • Remove foam packaging.• Raise the opener on

16INSTALLATION STEP 5Hang the OpenerThree representative installations are shown. Yours maybe different. Hanging brackets should be angled (Figure 1)

17To prevent possible SERIOUS INJURY or DEATH from electrocution:• Be sure power is NOT connected BEFORE installing door control.• Connect ONLY to 24

18INSTALLATION STEP 7Install the Lights • Press the release tabs on both sides of lens. Gentlyrotate lens back and downward until the lens hinge isin

19INSTALLATION STEP 9Electrical RequirementsTo avoid installation difficulties, do not run the opener at this time.To reduce the risk of electric shoc

2TABLE OF CONTENTSWhen you see these Safety Symbols and Signal Wordson the following pages, they will alert you to thepossibility of serious injury or

20Invisible Light BeamProtection AreaSafety Reversing Sensor6" (15 cm) max. above floorSafety Reversing Sensor6" (15 cm) max. above floorFac

21DOOR TRACK MOUNT (RIGHT SIDE)IndicatorLightLensLip SensorBracketDoorTrackFLOOR MOUNT (RIGHT SIDE)WALL MOUNT (RIGHT SIDE)IndicatorLightSensorBracketL

Invisible Light BeamProtection AreaSafety ReversingSensorSafety ReversingSensorConnect Wire toQuick-Connect TerminalsBell WireBell WireFinishedCeiling

23Fiberglass, aluminum or lightweight steel garage doors WILLREQUIRE reinforcement BEFORE installation of door bracket.Contact your door manufacturer

24Header WallVerticalCenterline ofGarage DoorFinished CeilingOptionalPlacementof DoorBracketHeaderBracketDoorBracket2x4 SupportFor a door with no expo

25INSTALLATION STEP 12Connect Door Arm to TrolleyFollow instructions which apply to your door type as illustrated below and on the following page.SECT

26Nuts5/16"-18LockWashers5/16"RingFastenerStraightArmBolts5/16"-18x7/8"DoorBracketClevis Pin5/16"x1-1/4"CurvedDoor ArmFi

27ADJUSTMENT STEP 1Adjust the UP and DOWN Travel LimitsLimit adjustment settings regulate the points at which the door will stop when moving up or dow

28ADJUSTMENT STEP 2Adjust the ForceForce adjustment controls are located on the right panelof the motor unit. Force adjustment settings regulate theam

29Without a properly installed safety reversal system, persons(particularly small children) could be SERIOUSLY INJUREDor KILLED by a closing garage do

3To prevent damage to garage door and opener:• ALWAYS disable locks BEFORE installing and operating the opener. • ONLY operate garage door opener at

30OPERATION Using Your Garage Door OpenerYour Security✚® opener and hand-held remote control have been factory-set to a matching code which changes wi

31To Open the Door ManuallyDISCONNECT THE TROLLEY:The door should be fully closed ifpossible. Pull down on theemergency release handle (sothat the tro

32CARE OF YOUR OPENERLIMIT AND FORCE ADJUSTMENTS:Weather conditions may causesome minor changes in dooroperation requiring some re-adjustments, partic

33HAVING A PROBLEM?1. My door will not close and the light bulbs blink onmy motor unit: The safety reversing sensor must beconnected and aligned corre

34Installed Safety Reversing SensorSafety Reversing SensorBell WireLED or Diagnostic LED"Learn" Button KG13975KG13975DiagnosticsLocated On M

35*3-Button RemotesIf provided with your garage door opener, the largebutton is factoryprogrammed tooperate it. Additionalbuttons on anySecurity✚®3-Bu

361. Enter a four digit personal identificationnumber (PIN) of your choice on thekeypad. Then press and hold ENTER.2. While holding the ENTER button,p

37710125NOTICE643291381LOCKLIGHT111235467Installation PartsREPAIR PARTSRail Assembly PartsKEY PART NO. NO. DESCRIPTION1 4A1008 Master link kit2

38Motor Unit Assembly PartsKEY PART NO. NO. DESCRIPTION 1 41A4371 Belt cap retainer 2 41A4885-5 Gear and sprocket assembly. Complete with: Sp

39LOCKLIGHTCLOSEDOPENLOCKLIGHT3-Button SECURITY✚®RemoteControl:Includes visor clip.SECURITY✚®Keyless Entry:Enables homeowner to operategarage door ope

4Safety Reversing SensorHeader WallAccess Door — — — — — — — —SafetyReversingSensorGap between floor and bottom of doormust not exceed 1

© 2011, The Chamberlain Group, Inc.114A3438B All Rights ReservedCHAMBERLAIN® SERVICE IS ON CALLOUR LARGE SERVICE ORGANIZATION SPANS AMERICAINSTALLATI

5AccessDoorSafetyReversing SensorSafetyReversingSensorGap between floor and bottom of doormust not exceed 1/4" (6 mm).GarageDoorHeaderWallHeaderB

6SECURITY✚®3-Button Remote ControlBelt Curved Door Arm Section Safety Labels and Literature Straight Door Arm Section Hanging Brackets Multi-Funct

7MasterLink (2) Idler Bolt (1)Nut3/8" (1)Trolley Threaded Shaft (1)Bolt 1/4"-20x1-3/4" (2)Lock Washer3/8" (1)Lock Nut1/4"-20

Front Rail(TO DOOR)WindowCut-OutScrewdriverIdlerPulleyHoleTabsBack Rails(TO MOTOR UNIT)TrolleyTaperedEndTaperedEndInner TrolleyWear PadsOuter TrolleyT

9To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of the opener.ASSEMBLY STEP 2Fasten the Rail to the