Chamberlain HS670 Manual do Utilizador

CONTROLLER BOARDGLModel HS670 is for vehicular passage gates only and is not intended for pedestrian passage gate use.MODEL HS670HEAVY-DUTY INDUSTRIAL

10INSTALLATIONVENT CAP1. Remove the threaded plug from the pump tank.2. Install the vent cap.NOTE: Never run the operator without the vent cap install

11INSTALLATIONGATE STOPS1. When properly installed the gate will open or close inapproximately 3" to 4" after limit shoe shuts the unit off,

12POWER WIRING INSTALLATIONWiring Specifications (STRANDED COPPER WIRE)On a Dual Gate System, each unit must be installed on ITS OWN separate circuits

13IMPORTANT NOTE: On three phase operators, power connectionsmust be properly phased. If phased incorrectly, the gate operatorwill run reversed. To co

14ADJUSTMENTTo reduce the risk of SEVERE INJURY or DEATH:• Disconnect power BEFORE performing ANY adjustments.ATTENTIONAVERTISSEMENT AVERTISSEMENTAVER

15UL325 ENTRAPMENT PROTECTIONPRIMARY ENTRAPMENT PROTECTION ADJUSTMENTSForce ControlSet the force control pot such that the unit will complete a fullcy

16CONTROL BOARD ILLUSTRATIONPROGRAMMINGRelay Drive Troubleshooting LEDs (D6)Terminal Troubleshooting LEDs (D11)Connector SAMS (J5)Connector (J2)Connec

17SLIDE/SWINGThis switch (S1-2) selects slide or swing gate operation, inorder to optimize gate behavior for specific application.SL = Slide, 1 second

18PROGRAM SETTINGS (DIP SWITCH #2) CONT’DEDGE/PHOTO OPENThis switch (S2-3) selects edge or photo sensor for the gateopening protection input.Open Phot

MMSecurity ModeTerminalsJumperHIGH SECURITY MODEJumperSecurity ModeTerminalsJumperNORMALSECURITY MODEOutputDurationTerminalsJumperOutputDurationTerm

2CARTON INVENTORYBefore beginning your installation check that all componentswere provided and received undamaged. Refer to list belowfor factory prov

20SEQUENCED ACCESS MANAGEMENT SYSTEM (SAMS)SAMS DEFINITIONThe Sequenced Access Management System or SAMS allows the customer more control when managin

21ACCESSORY WIRINGSTOP/RESET AUXILIARY CONTROL WIRINGTerminals 6 & 5 (Com) - OpenThese terminals are intended for use as a general open control.Ac

22CONTROL CONNECTION DIAGRAMSJ1 TERMINAL BLOCK38910 11 12 13 1424 VACR1R3R2R412467538910 11 12 13 141246751617151819 2021 22232425 262728Hard CloseCon

RPM Sensor (Hall Effect) Check for wear, oil damage and Xproper operationExternal Entrapment Check for proper operation XProtection SystemsGate Cautio

24GL BOARD FEATURESDIAGNOSTICS (LEDS AND CODES)There are three diagnostic LEDs. Two red LEDs (OL, CL) areindicators for the open and close limits. The

25OPERATOR FAILS TO RUNCONTACTOR CHATTERSWHEN OPERATOR BEGINSTO MOVEOPERATOR RUNS SLOWAND/OR TRIPS THEINTERNAL OVERLOAD1) No stop control2) Fault in t

26FAULT POSSIBLE CAUSE FIXMASTER OR SECONDOPERATOR IS NOTFUNCTIONING PROPERLYOPERATOR RUNS BUTTHEN STOPS ANDREVERSES DIRECTIONMOTOR RUNS BUT GATEDOES

27(A) BYPASS VALVE:It MUST be in the “automatic” position (horizontal). If it is inthe manual position, no fluid gets to the drive motors, sothey won’

28HYDRAULIC MOTORS1. The two hydraulic motors are “ROLLER VANE” type and aremachined to be free wheeling. Each motor has a displacementof 12 in3/rev.2

29HYDRAULIC DON’TS1. DO NOT use only one wrench to lighten hose swivel fittings.Use two wrenches, one to tighten and one to hold backopposite fitting.

3G. LIMIT SWITCHAll limit switches are oil tight and watertight, and of NEMA 3, 4,and 13 construction. Open switch for right hand, close switch forlef

30SINGLE PHASE WIRING DIAGRAM(LEFT)(RIGHT)OVERLOAD (SEE NOTE 6) BALDOR MOTOR CONNECTIONS EMMERSON MOTOR CONNECTIONS NOTES:1. Transformer primary volta

31THREE PHASE WIRING DIAGRAM(LEFT) (RIGHT) 4 NOTES:1. Transformer primary voltage same as operator line voltage 24V secondary 60VA.2. Wire color: 230V

32ELECTRICAL BOX2 13 9 12 9 4 1 11 8 10 7 3 5 6 14 15 ITEM PART # DESCRIPTION QTY NOTES PROVIDED IN KIT1 K001A5566 Control Board 1 Individual Part

33ILLUSTRATED PARTS131234567891010111412151633 ITEM PART # DESCRIPTION QTY NOTES PROVIDED IN KIT 1 K20-1100 Motor, 1HP 115/230V 1PH 1 1HP 1P

LIFTMASTER®TWO YEAR LIMITED WARRANTYThe Chamberlain Group, Inc. warrants to the final purchaser of this product, for the structure in which this produ

35OPERATOR NOTES

REPAIR PARTS AND SERVICE © 2011, The Chamberlain Group, Inc.01-18826J All Rights ReservedHOW TO ORDER REPAIR PARTSOUR LARGE SERVICE ORGANIZATION SPAN

4OPERATOR SPECIFICATIONSMODEL HS670 GC• 1 HP MotorGate Speed – 12"/sec.Maximum Gate Weight – 3000 lbs.Maximum V-Track Gate Width – 80 ft.MODEL HS

5CLASS I – RESIDENTIAL VEHICULAR GATE OPERATORA vehicular gate operator (or system) intended for use in a home of one-to four single family dwellings,

6SAFETY INSTALLATION INFORMATION1. Vehicular gate systems provide convenience and security. Gate systems are comprised of many component parts. The ga

7*Refer to loop manufacturer’s instructions for detailed installation and loop wiring instructions.GATE SYSTEM (MASTER/SECOND SLIDE GATE)GATE SYSTEM (

8NOT FOR USE AS PEDESTRIAN PASSAGE! This operator isintended for vehicular use only. To prevent INJURY to pedestrians,a separate pedestrian access sho

9NOTES: Installation shown is for a right-handed unit (on rightside of gate opening when inside looking out). Left-handed isopposite. For left-handed