Chamberlain WHISPER DRIVE WD912K Manual do Utilizador

Owner’s Manual Please read this manual and the enclosed safety materials carefully! Fasten the manual near the garage door after installation. The

10ASSEMBLY STEP 4Install the Belt and Set the TensionINSTALLING THE BELT1. Drop the notched side of the trolley clip into theretaining slot on top of

ASSEMBLY STEP 5Attach the Belt Cap Retainer• Position the belt cap retainer over the motor unitsprocket so the two holes in cap align with the twohole

12INSTALLATION STEP 1Determine the Header BracketLocationInstallation procedures vary according to garage doortypes. Follow the instructions which app

13Header WallVerticalCenterlineVerticalCenterlineof GarageDoor2x4UnfinishedCeiling2x4OPTIONALCEILING MOUNTFOR HEADER BRACKETStructuralSupportsONE-PIEC

14INSTALLATION STEP 2Install the Header BracketYou can attach the header bracket either to the wallabove the garage door, or to the ceiling. Follow th

15INSTALLATION STEP 3Attach the Rail to the HeaderBracket• Position the opener on the garage floor below theheader bracket. Use packing material as ap

16ONE-PIECE DOOR WITHOUT TRACKA 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Raise the opener onto a stepladder. You wi

17INSTALLATION STEP 5Hang the OpenerTwo representative installations are shown. Yoursmay be different. Hanging brackets should be angled(Figure 1) to

18LOCKLIGHTFigure 4 REMOVE COVERINSTALLATION STEP 6Install the Door ControlLocate door control within sight of the door at aminimum height of 5 feet

19INSTALLATION STEP 7Install the Lights • Press the release tabs on both sides of lens.Gently rotate lens back and downward until thelens hinge is in

2Introduction 2-7Safety symbol and signal word review...2Preparing your garage door ...3Tool

20INSTALLATION STEP 9Electrical RequirementsTo avoid installation difficulties, do not run theopener at this time.To reduce the risk of electric shoc

21Invisible Light BeamProtection AreaSensor Beam6" max.above floorSensor Beam6" max.above floorFacing the door from inside the garageINSTALL

22FLOOR MOUNT (RIGHT SIDE)WALL MOUNT (RIGHT SIDE)DOOR TRACK MOUNT (RIGHT SIDE)IndicatorlightLensLip SensorBracketDoorTrackSensorBracketExtensionBracke

23Carriage bolt 1/4"-20x1/2"LensWing nutFigure 4TROUBLESHOOTING THE SAFETY SENSORS1. If the sending eye indicator light does not glowsteadil

24INSTALLATION STEP 11Fasten the Door Bracket Follow instructions which apply to your door type asillustrated below or on the following page.A horizon

25Header WallVerticalCenterline ofGarage DoorFinished CeilingOptionalPlacementof DoorBracketHeaderBracketDoorBracket2x4 SupportFor a door with no expo

26INSTALLATION STEP 12Connect Door Arm to TrolleyFollow instructions which apply to your door type asillustrated below and on the following page.SECTI

27ALL ONE-PIECE DOORS1. Assemble the door arm, Figure 4:• Fasten the straight and curved door arm sectionstogether to the longest possible length (wit

28ADJUSTMENT STEP 1Adjust the UP and DOWN TravelLimitsLimit adjustment settings regulate the points at whichthe door will stop when moving up or down.

29ADJUSTMENT STEP 2Adjust the ForceForce adjustment controls are located on the rightpanel of the motor unit. Force adjustment settingsregulate the am

3To prevent damage to garage door and opener:•ALWAYS disable locks BEFORE installing andoperating the opener. • ONLY operate garage door opener at 120

Without a properly installed safety reversal system,persons (particularly small children) could beSERIOUSLY INJURED or KILLED by a closing garagedoor.

OPERATION 31IMPORTANT SAFETY INSTRUCTIONSTo reduce the risk of severe injury or death:Using Your Garage Door OpenerYour Security✚ opener and hand-held

To Open the Door ManuallyThe door should be fullyclosed if possible. Pull downon the emergency releasehandle and lift the doormanually. To reconnect t

33Care of Your OpenerLIMIT AND FORCEADJUSTMENTS:Weather conditions may causesome minor changes in dooroperation requiring somereadjustments, particula

34Having a Problem? (Continued)6. The garage door opens and closes by itself:• Be sure that all remote control push buttons areoff.• Remove the bell w

35LOCKLIGHT*Multi-Function RemotesIf provided with yourgarage door opener, thelarge button is factoryprogrammed to operateit. Additional buttons onany

361. Enter a four digit personalidentification number (PIN) of yourchoice on the keypad. Then pressand hold ENTER.2. While holding the ENTER button,pr

37139NOTICE56108UPCEILING MOUNT ONLY71432LOCKLIGHT11122133545891067Installation PartsREPAIR PARTSRail Assembly PartsKEY PARTNO. NO. DESCRIPTION1 4A100

Motor Unit Assembly Parts38DNUPBrownWire(Down)ContactLIMIT SWITCH ASSY.GreyWireYellowWire(Up)ContactCenter LimitContactDriveGear2437112157589171918610

39ACCESSORIES LOCKLIGHTCLOSEDOPEN3-Button SECURITY✚ RemoteControl:Includes visor clip.SECURITY✚ Keyless Entry:Enables homeowner to operategarage door

Safety Reversing SensorSupport bracket & fastening hardwareis required.See page 17. — — — — — — — —Header WallFINISHED CEILINGTorsio

©2003, The Chamberlain Group, Inc.114A2781 All Rights Reserved Printed in MexicoCHAMBERLAIN SERVICEIS ON CALLOUR LARGE SERVICE ORGANIZATIONSPANS AMERI

AccessDoorGap between floor andbottom of door mustnot exceed 1/4"SafetyReversing SensorSafetyReversingSensorCLOSED POSITIONHeaderBracketBeltPulle

6SECURITY✚Multi-FunctionRemote Control Transmitter (2)2-Conductor Bell WireWhite & White/RedTrolleyHeader BracketBeltCurved DoorArm SectionSafety

Hardware InventorySeparate all hardware and group as shown below for the assembly and installation procedures.7Lock Washer5/16" (4)Trolley Clip (

8ASSEMBLY STEP 1Assemble the Rail andAttach the Belt Pulley BracketTo avoid installation difficulties, do not run thegarage door opener until instruct

9ASSEMBLY STEP 2Install the Trolley• As a temporary stop, insert a screwdriver into thehole in the front end of the rail.• Slide the trolley assembly