Chamberlain door opener Manual do Utilizador

This Operator Features the EnhancedRadio Receiver Built on BoardO W N E R ’ S M A N U A LGHINDUSTRIAL DUTY COMMERCIAL DOOR OPERATORogicL 3NOT FOR RE

10To reduce the risk of SEVERE INJURY or DEATH:• ANY maintenance to the operator or in the area near the operator MUST NOT be performed until disconn

11CONTROL WIRING CONNECTIONS1. Connect control wires to the P1 terminal block located on the logic board as shown.2. Connect conduit with all contro

12OpenCloseStopMaintenanceAlert LEDOpen/CloseSingle Button(WH)(RD)Sensing EdgeCPS-L &CPS-LN4Timer DefeatSwitchR1R2R3Radio Control(24V DC only)Neut

13U1POWER TIMER DEFEAT MAS 4 MRT 1 RADIO MID 2 TIMER TIMER ENABLE T TS FSTS E2 RELAY A RELAY B D1 DIAG C2 B2 PROG 3 24V AC 24V AC TIMER DEFEAT CMN MAS

14U1POWER TIMER DEFEAT MAS 4 MRT 1 RADIO MID 2 TIMER TIMER ENABLE T TS FSTS E2 RELAY A RELAY B D1 DIAG C2 B2 PROG 3 24V AC 24V AC TIMER DEFEAT CMN MAS

15U1POWERTIMERDEFEATMAS4MRT1RADIOMID2TIMERTIMERENABLETTSFSTSE2RELAY ARELAY BD1 DIAGC2B2 PROG324VAC24VACTIMERDEFEATCMNMASEYESEDGEOPENCLOSESTOPCMNSBC111

16DETERMINE AND SET WIRING TYPERead the descriptions of the different wiring types to determine which setting will be correct for each application.SET

17FAILSAFE WIRING TYPESTYPETS Momentary contact to open, close, and stop with open override and Timer To Close. Every device that causes door to open

18SINGLE BUTTON REMOTE CONTROL PROGRAMMED AS A SINGLE BUTTON CONTROL (SBC)This function programs a remote control as a wireless single button control.

193-BUTTON REMOTE CONTROLSYour 315MHz Security✚®or dip switch remote control can be programmed to operate as a 3-button wireless control station: the

2When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you d

20MAINTENANCE ALERT SYSTEM (MAS)Feature: An internal cycle counter will activate a flashing LED on the 3-button control station when the preset number

21Operation will vary depending on wiring typeSELECTOR DIALOperation will vary depending on wiring typeSELECTOR DIALOPEN MID STOPFeature: The mid stop

22TIMER TO CLOSEPROGRAM TIMER TO CLOSE BY EXAMPLE (Method 2):To Program:1. Close the door.2. Turn the selector dial to PROGRAM.3. Press and hold TI

23MAXIMUM RUN TIMER (MRT)Feature: The operator can learn the time it takes to open or close the door plus an additional 10 seconds.Benefit: If the ope

24RESETTING FACTORY DEFAULTS - CLEARING MEMORYTo reset most of the user installed settings back to factory defaults:1. Turn the selector dial to DIAG

25MAINTENANCE SCHEDULEFor use with Maintenance Alert System.Check at the intervals listed in the following chart:HOW TO ORDER REPAIR PARTSOUR LARGE SE

26DIAGNOSTIC CHARTThe logic board has several LEDs to assist in the installation and troubleshooting of the operator. The following chart should assis

27TROUBLESHOOTING GUIDEFAULT POSSIBLE CAUSE FIXTHE OPERATOR WILL NOT RESPOND TO ANY COMMANDSa) No power supplyb) Operator control station is wired wr

28TROUBLESHOOTING ERROR CODESLogic 3.0 operators incorporate a self diagnostic feature built into the MAS LED. In addition to indicating when routing

29TROUBLESHOOTING RADIO FUNCTIONALITYThe error codes will display at the radio LED.NOTE: Radio receiver is compatible with 315 MHz remotes.ERROR CODE

3Before beginning your installation check that all components were provided.14.00"Hand Chain Wheel SeeNote #1See Note #2AXBYCDYSee Note #3NOTES:1

306 9 8 1 4 7 5 2 11 10 3 K1 K2 (K72-10047-1)(K72-12515-1)(K72-10047)ELECTRICAL BOX

31For replacement of electrical box, motor or brake components be sure to match model number of your unit to kit number below to ensure proper voltage

32134K5 (K75-12829) (K75-12830)(K75-12831) (K75-12832)(K75-12833)K1 (K75-12584)(K75-12585)(K75-12586)25K4 (K75-30737)6171819207K3 (K72-12789)131389101

33SERVICE KITSITEM PART # DESCRIPTIONK1 K75-12584 Brake kit - 115 Volt modelsK75-12585 Brake kit - 230-460 Volt modelsK75-12586 Brake kit - 575

34OPERATOR NOTES

35OPERATOR NOTES

CONTROL CONNECTION DIAGRAMIMPORTANT NOTES:1. The 3-Button Control Station provided must be connected for operation.2. If a STOP button is not used, a

4SAFETYDISCONNECT:. . . . . . . . . . . Floor level chain hoist with electricalinterlock for manual door operationCLUTCH (Optional): . . . . . . . .

5It is imperative that the wall or mounting surface provide adequate support for the operator.This surface must: a. Be rigid to prevent play betwee

6IMPORTANT NOTE: Before your operator is installed, be sure the door has been properly aligned and is working smoothly. The operator may be wall moun

7MANUAL OPERATIONThis operator has provisions for manually operating the door in case of emergency or power failure. These operators are equipped with

8ENTRAPMENT PROTECTION ACCESSORIES (OPTIONAL)PHOTO EYES AND SENSING EDGESSensing devices provided for door industry type operators with an isolated no

9ADJUST TORQUE LIMITER CLUTCH(OPTIONAL MODIFICATION)1. Loosen set screws on clutch nut.2. Back off clutch nut until there is very little tension on