Chamberlain 8200 1/2 HP Manual do Utilizador

Garage Door OpenerModel 8200 Series1/2 HPFor Residential Use Only Owner's Manual Please read this manual and the enclosed safety materials caref

Assembly Step 4Install the Belt & Set the Belt TensionSerious injury can result if fingers becomeentangled in moving opener sprocket. Attachbelt c

Hex Screws# 8 x 3/8"Belt CapRetainerOpener SprocketMounting PlateAssembly Step 5Attach the Belt Cap RetainerIMPORTANT INSTALLATION INSTRUCTIONSTo

• Open your door to the highestpoint of travel as shown. Drawan intersecting horizontal lineon the header wall 2" abovethe high point. This heigh

Header WallVerticalCenterlineVerticalCenterline ofGarage Door2x4UnfinishedCeilingStructuralSupports2x4OPTIONAL CEILING MOUNTFOR HEADER BRACKET• Close

Lag Screws5/16"x9x1-5/8"HighestPoint of Travel(of Garage Door)VerticalCenterLineHeaderWallGarageDoorUPCEILING MOUNT ONLYWallMounting HolesOp

HeaderBracketBelt PulleyBracketTemporarySupportHeader WallGarageDoor,Liftmaster Synchro DriveTee Rail to Header Bracket5/16/92T-railClevis Pin5/16&quo

Installation Step 4Position the OpenerFollow instructions which apply to your door typeas illustrated.To prevent damage to steel, aluminum,fiberglass

Installation Step 5Hang the OpenerTwo representative installations are shown.Yours may be different. Hanging brackets shouldbe angled, Figure 1, to pr

18Installation Step 6Install the Multi-FunctionDoor Control Panel6ABx1-1/4" ScrewMulti-Function Door ControlInsulated StaplesDry Wall AnchorsScre

• Install a 75 watt maximum light bulb in eachsocket. The lights will turn ON and remain lit forapproximately 4-1/2 minutes when power isconnected. Th

Start by reviewing these important safety alert symbols2Contents PageA review of safety alert symbols...2You'll ne

To prevent electrocution, remove power fromthe garage door opener andfrom the circuityou plan to use for the permanent connection.To reduce the risk o

Without a properly working safety reversingsensor, persons (particularly children) couldbe injured or killed by a closing garage door.Read and follow

Installation Step 10Install the Safety Reversing Sensor22FLOOR MOUNT (Right Side)WALL MOUNT (Right Side)DOOR TRACK MOUNT (Right Side)Indicator lightLe

23Invisible Light BeamProtection AreaSensorSensorConnect Wire toOpener TerminalsBell WireBell WireFinishedCeilingOPENER TERMINAL SCREWSSensorConnectio

Installation Step 11Fasten Door Bracket Follow instructions which apply to your door typeas illustrated below or on page 25.To prevent damage to steel

Horizontal and verticalreinforcement is needed forlightweight garage doors(fiberglass, aluminum, steel, door with glass panel, etc.).(Not Provided)Hea

Ring FastenerDoorBracketClevis Pin5/16"x1-1/4"CurvedDoor ArmStraightDoor ArmClevis Pin5/16"x1"LockWashers5/16"Nuts5/16"-

Nuts5/16"-18LockWashers5/16"RingFastenerStraightArmScrews5/16"-18x7/8DoorBracketClevis Pin5/16"x1-1/4"CurvedDoor ArmDoor ArmF

Adjustment Step 1Adjust the UP and DOWN LimitsDo not make any limit adjustments until theSafety Reversing Sensors are completelyinstalled.28Limit adju

Adjustment Step 2Adjust the ForceToo much force on the door will interfere withthe proper operation of the safety reversesystem. The door might not re

PliersWire CuttersClaw HammerHack SawScrewdriverAdjustable End Wrench1/2" and 7/16" Socketsand WrenchDrillTape Measure21StepladderPencil3/16

Adjustment Step 4Test the Safety Reverse SystemTest:• With the door fully open, place a one-inch board(or a 2x4 laid flat) on the floor, centered unde

Once a MonthManually operate door. If it is unbalanced orbinding, call for professional garage door service.Check to be sure door opens and closes ful

To open the doormanually:The door should be fullyclosed if possible. Pulldown on the manualrelease handle and liftthe door manually. Toreconnect the d

KGKG1397513975123Smart (learn)ButtonSECURITY✚Garage Door OpenerIndicatorLightRIGHTSIDE PANELKGKG139751397512333Figure 2SECURITY✚Multi-Function Remote

1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light,check the fuse box or the circuit breaker. (Some outlets

Having a Problem? (continued)Situation Probable Cause & SolutionThe opener strainsor maximum force isneeded to operatethe door:The door may be out

91011NOTICE56UPCEILING MOUNT ONLY874321LOCKLIGHT1312213345105RAIL GREASENO. 83A48976Repair PartsRail Assembly PartsInstallation Parts36KEY PARTNO. NO.

Repair PartsOpener Assembly Parts212101543DNUPBrownWire(Down)ContactLIMIT SWITCH ASSY.GreyWireYellowWire(Up)ContactCenter LimitContactDriveGear1156798

Accessories Available for your Opener38Outside Keylock:Opens the garage doorautomatically from outside whenremote control is not handy.To Add the Keyl

IndexAccess Door/Outside Quick Release Accessory...4, 5Electr

4Safety Reversing SensorHorizontal and vertical reinforcementis needed for lightweight garage doors(fiberglass, steel, aluminum, door with glass panel

CHAMBERLAIN SERVICEIS ON CALLOUR LARGE SERVICE ORGANIZATIONSPANS AMERICAINSTALLATION AND SERVICE INFORMATION IS ASNEAR AS YOUR TELEPHONE SIX DAYS A WE

Safety Reversing SensorFINISHED CEILINGSupport bracket& fasteninghardware is required.See page 17.SafetyReversingSensorHeaderWallAccess DoorGap be

TrolleyHeader BracketHanging BracketsBeltCurved DoorArm SectionStraight DoorArm SectionSafety LabelsandLiteratureLight Lens (2)Rail Brace (3)T-railCen

Lock Washer5/16" (4)Nut 5/16"-18 (6)Clevis Pin5/16"x2-3/4" (1)NOTICEHandleInsulatedStaples (10)ASSEMBLYINSTALLATIONDry Wall Anchor

8Assembly Step 1Assemble the T-rail &Attach the Belt Pulley BracketT-RAIL BACK(TO OPENER)T-RAIL FRONT(TO DOOR)Belt pulley bracketattaches to FRONT

Assembly Step 2Install the Trolley on the T-rail9• As a temporary stop, insert a screwdriver into thehole in the front end of the T-rail.• Slide the t