Chamberlain 3585 3/4 HP Manual do Utilizador

The Chamberlain Group, Inc.845 Larch AvenueElmhurst, Illinois 60126-1196www.liftmaster.comGARAGE DOOR OPENERModel 3585 3/4 HPFor Residential Use Only

HeaderBracketBelt PulleyBracketTemporarySupportHeader WallGarageDoorClevis Pin5/16"x2-3/4"Ring FastenerHeader BracketBelt PulleyBracketRail1

11ONE-PIECE DOOR WITHOUT TRACKA 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging.• Raise the opener o

12Bracket(Not Provided)Lag Screws5/16"-18x1-7/8"(Not Provided)Bolt 5/16"-18x7/8"Lock Washer 5/16"Nut 5/16"-18 FINISHED

13INSTALLATION STEP 6Install the Control ConsoleLocate control console within sight of door, at a minimumheight of 5' (1.5 m) where small childre

14LensHinge100 Watt (Max)Standard Light BulbRelease Tab100 Watt (Max)Standard Light BulbINSTALLATION STEP 7Install the Light • Press the release tabs

15INSTALLATION STEP 9Electrical RequirementsTo avoid installation difficulties, do not run theopener at this time.To reduce the risk of electric shock

16Invisible Light BeamProtection AreaSafety Reversing Sensor6" (15 cm) max. above floorSafety Reversing Sensor6" (15 cm) max. above floorFac

17DOOR TRACK MOUNT (RIGHT SIDE)IndicatorLightLensLip SensorBracketDoorTrackFLOOR MOUNT (RIGHT SIDE)WALL MOUNT (RIGHT SIDE)IndicatorLightSensorBracketL

18Invisible Light BeamProtection AreaSafety Reversing SensorSafety Reversing SensorConnect Wire toOpener Quick-Connect TerminalsBell WireBell WireFini

19Fiberglass, aluminum or lightweight steel garage doors WILLREQUIRE reinforcement BEFORE installation of door bracket.Contact your door manufacturer

2Introduction 2-5Safety symbol and signal word review...2Preparing your garage door ...3Tool

20Header WallVerticalCenterline ofGarage DoorFinished CeilingOptionalPlacementof DoorBracketHeaderBracketDoorBracket2x4 SupportFor a door with no expo

21INSTALLATION STEP 12Connect Door Arm to TrolleyFollow instructions which apply to your door type asillustrated below and on the following page.SECTI

22ALL ONE-PIECE DOORS1. Assemble the door arm, Figure 4:• Fasten the straight and curved door arm sectionstogether to the longest possible length (wit

23ADJUSTMENT STEP 1Adjust the UP and DOWN Travel LimitsLimit adjustment settings regulate the points at which thedoor will stop when moving up or down

24ADJUSTMENT STEP 2Adjust the ForceForce adjustment controls are located on the back panelof the motor unit. Force adjustment settings regulate theamo

25Without a properly installed safety reversal system, persons(particularly small children) could be SERIOUSLY INJUREDor KILLED by a closing garage do

26OPERATIONIMPORTANT SAFETY INSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:Using Your Garage Door OpenerYour Security✚®opener and hand-held

27Using the Wall-Mounted ControlConsoleTHE LCD MOTION DETECTING CONTROL CONSOLEPress the push bar toopen or close thedoor. Press again toreverse the d

28Using the Remote ControlNOTE: To activate the remote control functions, pull outthe plastic pull tab protruding from the remote controlhousing.This

29CARE OF YOUR OPENERLIMIT AND FORCE ADJUSTMENTS:Weather conditions may causesome minor changes in dooroperation requiring some re-adjustments, partic

3To prevent damage to garage door and opener:• ALWAYS disable locks BEFORE installing and operating theopener. • ONLY operate garage door opener at 12

30HAVING A PROBLEM?1. My door will not close and the light bulbs blink onmy motor unit: The safety reversing sensor must beconnected and aligned corre

31Bell WireSafety Reversing SensorKG13975KG13975DiagnosticsLocated OnMotor Unit"Learn" Button LED or Diagnostic LED Installed Safety R

32Meaning: This message will appear if the Safety Reversing Sensors are out ofalignment, if they are blocked or if the wiring is disconnected. To clea

33*3-Button RemotesIf provided with your garage door opener, the largebutton is factory programmed to operate it. Additionalbuttons on anySecurity✚®3-

34To Add, Reprogram or Change a Keyless Entry PINNOTE: Your new Keyless Entry must be programmed to operate your garage door opener.USING THE “LEARN”

3525613784REPAIR PARTSRail Assembly PartsKEY PARTNO. NO. DESCRIPTION1 4A1008 Master link kit2 41B5424 Belt pulley bracket3 41B3869-1 Complete trolley

36Motor Unit Assembly PartsDNUPBrownWire(Down)ContactLIMIT SWITCH ASSEMBLYGreyWireYellowWire(Up)ContactCenter LimitContactDriveGear243115198A175189101

37ACCESSORIES 370LM2778BD41A52811702LMOutside Quick Release:Required for a garage with NOaccess door. Enables homeownerto open garage door manually fr

38NOTES

39NOTES

FINISHED CEILINGSupport bracket& fasteninghardware is required.See page 12.SafetyReversing SensorHeaderWallAccess DoorSafety Reversing SensorGap b

© 2007, The Chamberlain Group, Inc.114A3396 All Rights ReservedLIFTMASTER®SERVICE ISON CALLOUR LARGE SERVICE ORGANIZATIONSPANS AMERICAINSTALLATION AND

5Your garage door opener is packaged in two cartonswhich contain the motor unit and all parts illustratedbelow. Accessories will depend on the model p

To avoid SERIOUS damage to opener, ONLY usebolts/fasteners mounted in top of motor unit.WARNINGCAUTIONWARNINGWARNINGASSEMBLY STEP 1Attach the Rail to

7INSTALLATIONIMPORTANT INSTALLATION INSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:WARNINGWARNINGWARNING1. READ AND FOLLOW ALL INSTALLATION

8INSTALLATION STEP 1Determine the Header BracketLocationInstallation procedures vary according to garage doortypes. Follow the instructions which appl

9INSTALLATION STEP 2Install the Header BracketYou can attach the header bracket either to the wallabove the garage door, or to the ceiling. Follow the