Chamberlain PD200 Manual do Utilizador

GARAGE DOOR OPENERSeries PD2001/2 HPFor Residential Use Only Complies with UL 325regulations effectiveJanuary 1, 1993®Owner’s Manual Please read this

10ASSEMBLY STEP 4Install the Chain/Cableand Attach the Sprocket CoverINSTALLING THE CHAIN/CABLE1. Pull the cable loop fromthe carton and fasten itto t

ASSEMBLY STEP 5Tighten the Chain and Cable• Spin the inner nut and lock washer down thetrolley threaded shaft, away from the trolley.• To tighten the

12INSTALLATION STEP 1Determine the Header BracketLocationInstallation procedures vary according to garage doortypes. Follow the instructions which app

13Header WallVerticalCenterlineVerticalCenterlineof GarageDoor2x4UnfinishedCeiling2x4OPTIONALCEILING MOUNTFOR HEADER BRACKETStructuralSupportsONE-PIEC

14INSTALLATION STEP 2Install the Header BracketYou can attach the header bracket either to the wallabove the garage door, or to the ceiling. Follow th

Clevis Pin5/16" x 2-3/4"Ring Fastener15INSTALLATION STEP 3Attach the T-Rail to the HeaderBracket• Position the opener on the garage floor b

16ONE-PIECE DOOR WITHOUT TRACK• With the door fully open and parallel to the floor,measure the distance from the floor to the top ofthe door.• Using a

17INSTALLATION STEP 5Hang the OpenerTwo representative installations are shown. Yoursmay be different. Hanging brackets should be angled(Figure 1) to

To prevent possible serious injury or death fromelectrocution:• Be sure power is not connected before installing doorcontrol.• Connect only to 24 VOLT

19INSTALLATION STEP 7Install the Light and LensINSTALL THE LIGHT• Install a 75 watt maximum light bulb in socket. Thelight will turn ON and remain lit

2Introduction Pages 2-7Safety symbol and signal word review...2Preparing your garage door ...

20INSTALLATION STEP 9Electrical RequirementsTo avoid installation difficulties, do not run theopener at this time.To reduce the risk of electric shock

21Invisible Light BeamProtection AreaSensor Beam6" max.above floorSensor Beam6" max.above floorFacing the door from inside the garageINSTALL

22FLOOR MOUNT (RIGHT SIDE)WALL MOUNT (RIGHT SIDE)DOOR TRACK MOUNT (RIGHT SIDE)Indicator lightLensLip SensorBracketDoorTrackSensorBracketExtensionBrack

231/4"-20x1/2"Carriage boltLensWing nutFigure 4MOUNTING AND WIRING THE SAFETY SENSORS• Slide a 1/4"-20x1/2" carriage bolt head int

24To prevent damage to garage door, reinforce inside ofdoor with angle iron both vertically and horizontally.INSTALLATION STEP 11Fasten the Door Brack

25ONE-PIECE DOORS Please read and comply with the warnings andreinforcement instructions on the previous page. Theyapply to one-piece doors also.• Cen

26INSTALLATION STEP 12Connect Door Arm to TrolleyFollow instructions which apply to your door type asillustrated below and on the following page.SECTI

ALL ONE-PIECE DOORS1. Assemble the door arm:• Fasten the straight and curved door arm sectionstogether to the longest possible length (with a 2or 3 ho

28ADJUSTMENT STEP 1Adjust the UP and DOWN TravelLimitsLimit adjustment settings regulate the points at whichthe door will stop when moving up or down.

ADJUSTMENT STEP 2Adjust the ForceForce adjustment controls are located on the backpanel of the motor unit. Force adjustment settingsregulate the amoun

3PliersWire CuttersClaw HammerHack SawScrewdriverAdjustable End Wrench1/2" and 7/16" Socketsand WrenchDrillTape Measure21StepladderPencil3/1

Without a properly installed safety reversal system,persons (particularly small children) could beSERIOUSLY INJURED or KILLED by a closing garagedoor.

OPERATION 31IMPORTANT SAFETY INSTRUCTIONS1. READ AND FOLLOW ALL WARNINGS ANDINSTRUCTIONS.2. ALWAYS keep remote controls out of reach of children.NEVER

To Open the Door ManuallyThe door should be fullyclosed if possible. Pull downon the emergency releasehandle and lift the doormanually. To reconnect t

33Care of Your OpenerLIMIT AND FORCE ADJUSTMENTS:Weather conditions may causesome minor changes in dooroperation requiring somereadjustments, particul

34Having a Problem? (Continued)6. The garage door opens and closes by itself:• Be sure that all remote control push buttons areoff.• Remove the bell w

LOCKLIGHT*Multi-Function RemotesIf supplied with yourgarage door opener,the large button isfactory programmed tooperate it. Additionalbuttons on anySe

1. Enter a four digit personalidentification number (PIN) of yourchoice on the keypad. Then pressand hold ENTER.2. While holding the ENTER button,pres

7UPCEILING MOUNT ONLY91011NOTICE56841213321LOCKLIGHT13367455RAIL GREASENO. 83A482Installation Parts37REPAIR PARTSRail Assembly PartsKEY PARTNO. NO. DE

Motor Unit Assembly Parts38DNUPBrownWire(Down)ContactLIMIT SWITCHASSEMBLYGreyWireYellowWire(Up)ContactCenter LimitContactDriveGear21081314151619453792

LOCKLIGHTLOCKLIGHT39ACCESSORIES SECURITY✚ Multi-FunctionRemote Control:Includes visor clip.SECURITY✚ Keyless Entry:Enables homeowner to operate garage

Safety Reversing SensorSupport bracket & fastening hardwareis required.See page 17. — — — — — — — —Door CenterHeader WallFINISHED CE

CHAMBERLAIN SERVICEIS ON CALLOUR LARGE SERVICE ORGANIZATIONSPANS AMERICAINSTALLATION AND SERVICE INFORMATION IS ASNEAR AS YOUR TELEPHONE SIX DAYS A WE

CLOSED POSITIONAccessDoorGap between floor and bottom of door must not exceed 1/4"SafetyReversing SensorSafetyReversingSensorWall-MountedDoor Con

6Cable PulleyBracket2-Conductor Bell WireWhite & White/RedTrolleyHeader BracketChain and Cable inDispensing CartonCurved DoorArm SectionStraight D

Hardware InventorySeparate all hardware and group as shown below for the assembly and installation procedures.7Lock Washer5/16" (4)Lock Nut1/4&qu

8ASSEMBLY STEP 1Assemble the T-Rail andAttach the Cable Pulley BracketTo avoid installation difficulties, do not run thegarage door opener until instr

9ASSEMBLY STEP 2Install the Trolley• Attach the trolley threaded shaft to the trolley withthe lock washer and nuts as shown.• As a temporary stop, ins