Chamberlain CG40DM Manual do Utilizador

The Chamberlain Group, Inc.845 Larch AvenueElmhurst, Illinois 60126-1196www.chamberlain.comGARAGE DOOR OPENERModel CG40DM 1/2 HPFor Residential Use On

10Trolley Threaded ShaftRound HoleFigure 4Trolley Threaded ShaftLock 5/16"WasherInner Nut5/16"To avoid possible SERIOUS INJURY to fi ngers fr

11INSTALLATIONASSEMBLY STEP 5Tighten the Chain • Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley.• To ti

12INSTALLATION STEP 1Determine the Header Bracket LocationInstallation procedures vary according to garage door types. Follow the instructions which a

13INSTALLATION STEP 2Install the Header BracketYou can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow t

14INSTALLATION STEP 3Attach the Rail to the Header Bracket• Position the opener on the garage fl oor below the header bracket. Use packing material a

15INSTALLATION STEP 5Hang the OpenerThree representative installations are shown. Yours may be different. Hanging brackets should be angled(Figure 1)

16To prevent possible SERIOUS INJURY or DEATH from electrocution:• Be sure power is NOT connected BEFORE installing door control.• Connect ONLY to

17INSTALLATION STEP 7Install the Light and LensINSTALL THE LIGHT• Install an A19 standard neck, 75 watt maximum light bulb in the socket. The light

18INSTALLATION STEP 9Electrical RequirementsTo avoid installation diffi culties, do not run the opener at this time.To reduce the risk of electric shoc

19INSTALLATION STEP 10Install The Protector System®The safety reversing sensor must be connected and aligned correctly before the garage door opener w

2TABLE OF CONTENTSWhen you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury

20INSTALLING THE BRACKETSBe sure power to the opener is disconnected. Install and align the brackets so the sensors will face each other across the ga

21MOUNTING AND WIRING THE SAFETYREVERSING SENSORSMounting:• Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor. Use wing

2212 3Figure 10— Finished Ceiling —Bell WireBell WireConnect Wire to Screw TerminalsSafety Reversing SensorSafety Reversing SensorInvisible Light Beam

23INSTALLATION STEP 11Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page.A horizo

24ONE-PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also.•

25INSTALLATION STEP 12Connect Door Arm to TrolleyFollow instructions which apply to your door type as illustrated below and on the following page.SECT

26ALL ONE-PIECE DOORS1. Assemble the door arm, Figure 5:IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm. •

27ADJUSTMENT STEP 1Adjust the UP and DOWN Travel LimitsLimit adjustment settings regulate the points at which the door will stop when moving up or dow

28ADJUSTMENT STEP 2Adjust the ForceForce adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the a

29Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage

3To prevent damage to garage door and opener:• ALWAYS disable locks BEFORE installing and operating the opener. • ONLY operate garage door opener

30OPERATION Using Your Garage Door OpenerYour Security✚® opener and hand-held remote control have been factory-set to a matching code which changes wi

31To Open the Door ManuallyDISCONNECT THE TROLLEY:The door should be fully closed if possible. Pull down on the emergency release handle(so that the t

32CARE OF YOUR OPENERLIMIT AND FORCE ADJUSTMENTS:Weather conditions may cause some minor changes in door operation requiring some re-adjustments, part

33HAVING A PROBLEM?1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned c

34KGKG13975139751231Your garage door opener is programmed withself-diagnostic capabilities. The “Learn” button/diagnostic LED will fl ash a number of t

35*3-Button RemotesIf provided with your garage door opener, the large button is factory programmed to operate it. Additional buttons on any Security✚

361. Press and release the “learn” button on motor unit. The learn indicator light will glow steadily for 30 seconds.2. Within 30 seconds, enter a

377 10 12 5 6 4 9 13 8 1 11 3 2 REPAIR PARTSRail Assembly Parts214356KEY PART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41C5141-1 Compl

38Motor Unit Assembly PartsDNUP2135478961911131615141210151718LIMIT SWITCH ASSEMBLYBrown Wire(Down) ContactGrey WireYellow Wire(Up) ContactCenter Limi

39ACCESSORIES 3-Button SECURITY✚® Remote Control:Includes visor clip.SECURITY✚® Keyless Entry:Enables homeowner to operate garage door opener from out

4 — — — — — — — —PlanningIdentify the type and height of your garage door. Survey your garage area to see if any of the conditions below

CHAMBERLAIN® GARAGE DOOR OPENER ONE-YEAR LIMITED WARRANTYFOUR-YEAR MOTOR LIMITED WARRANTYThe Chamberlain Group, Inc. (“Seller”) warrants to the fi rst

5Planning (Continued)ONE-PIECE DOOR INSTALLATIONS• Generally, a one-piece door does not require reinforcement. If your door is lightweight, refer to

6Your garage door opener is packaged in one carton which contains the motor unit and all parts illustrated below. Accessories will depend on the model

7Hardware InventorySeparate all hardware and group as shown below for the assembly and installation procedures.INSTALLATION HARDWAREASSEMBLY HARDWAREI

8ASSEMBLY STEP 1Assemble the Rail & Install the TrolleyTo avoid installation diffi culties, do not run the garage door opener until instructed to d

9To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of the opener.ASSEMBLY STEP 2Fasten the Rail to the